AM02/Pro deep bottom and sata cable?

[Alkbottle]

Hi;

Anyone knows if the AM03 base plate, deep bottom and sata+power cable is sold seperately?

I ask because I got an AM02Pro, a nice device, but I would like to add that second Sata SSD which the AM03 is capable of and has space for.

Is a 3d model available for the bottom?
I would 3d print it.

Leaves only the sata+power cable.
That would be nice to puchase, otherwise I can make one myself.

Best regards Alkbottle

[Gabe]

Not by the company.

Perhaps someone has modded or created an AM02 case that can do so, but it would be completely 3rd party.

[barry777]

Due to limited internal space, AM02/AM02 Pro does not support expansion of 2.5-inch SSD

[Alkbottle]

So, did some research.

The AM02/Pro is based on the AM03, which in turn is a (HYSTOU, VENOEN, WEIDAN, M6) AMD 3750H based mini pc.
They all share the same mainboard HDF520007-P01, the layout of the AM02/PRO in this regard is VERY similar.

Okay, why is that important? The AM03 has the SATA port and a 5 pin JST 1.25mm molex picoblade connector which provides 5V and GND.
The AM02/Pro has the same SATA port but the base plate covers the 5 pin JST 1.25mm molex picoblade board to wire socket, it is there just covered.
Here a picture of the AM03:
AM03 Mainboard base shot

Here a picture of the AM02/Pro:
AM02/Pro Mainboard base shot

Notice in the AM02/Pro mainboard base shot the tiny beige connector in the left bottom corner? That's the 5 pin JST 1.25mm socket.
I did disassemble the machine (warning ribbon cable connecting mobo and front IO) and cut the plastic away covering the socket, I did some multimeter magic while the machine was powered on.

The pin out is as following with respective alignment:
[NVME] slot on top
[SATA] facing left side
[ I I . I I ] sata power facing left side
GND GND NC +5V +5V
[RAM] facing viewer

Here a picture of my DIY cable from scraps of several older machines. The Sata power connector was used as a donor.
FYI it is a COMAX model with the top plate removed for DIY soldering prior to assembly.
Crimped power cable JST 1.25mm
In theory something like the DELOCK 85336 power cable should work when recrimped to the JST 1.25mm 5pin connector.

The SATA port is special in that regard, that you will need an angled cable facing away from the alingment notch, like this one from LINDY Art.-Nr. 33350 :
Angled SATA cable

Next step is to model a base with the footprint of the AM02/Pro and the frame of a 2,5" sata ssd.
I will model that base, probably a bit deeper than the original base of an AM03 to provide more airflow and comfortable wire routing, once I have a prototype I will post that STL file for whoever wants to embed a 2,5" sata ssd into his AM02/Pro.

[MiyaCulpa]

I am attaching the construction photos to give you an idea. Although there is a SATA and sata power connection, I cannot understand why the manufacturer did not make the bottom cover accordingly , with cables the cost would not exceed a few dollars

20240529_121213.jpg (3.07 MiB) Viewed 3743 times

20240529_124223.jpg (1.04 MiB) Viewed 3727 times

20240529_130039.jpg (2.33 MiB) Viewed 3743 times

20240529_124333.jpg (2.38 MiB) Viewed 3743 times

20240529_130615.jpg (1.93 MiB) Viewed 3743 times

20240529_124348.jpg (1016.83 KiB) Viewed 3743 times

[MiyaCulpa]

Work finished
The 8mm piece in between and the HDD holder can be removed and returned to its original state.

20240529_152506.jpg (2.6 MiB) Viewed 3742 times

20240529_183904.jpg (2.76 MiB) Viewed 3742 times

20240529_184003.jpg (3.4 MiB) Viewed 3742 times

20240529_184140.jpg (2.18 MiB) Viewed 3742 times

20240529_184159.jpg (2.36 MiB) Viewed 3742 times

20240529_184345.jpg (3.16 MiB) Viewed 3742 times

[MiyaCulpa]

notice : If you are install an old type thick 2.5" hard disk and the connection cables will be normal SATA cables, cut the piece in between as 12-13mm.
I installed a thin 7mm hard disk and used thin cables, an 8mm spacer was sufficient.